Skip to main content

Hyundai Air Conditioner Error Codes

 Protection and Failure Display

  • When protection display is available, controller will show error code, digital LED shows error code and setting temperature by turns.
  • If there is more than one failure, it will show at first that in front of the error list.
  • Protection display function can be selected in hardware, and the default don’t display;
  • To insure of in and out communist is credibility, the failures relate to outdoor unit will remain failure state for 2 minutes max after recovered.
  • In all failures, only sensor failures don’t have to repower to cancel.
Hyundai Air Conditioner Error Codes
Hyundai Air Conditioner Error Codes

Error List

Error CodeLed CodeFailure Type
E0RUN, TIMER–both winkingIn and out communication failure
ECRUN, TIMER–both winkingOutdoor communication failure
E1RUN-1 time/8sOutdoor sensor
E2RUN-2 times /8sIndoor coil temperature sensor
E3RUN-3 times /8sOutdoor coil temperature sensor
E4RUN-4 times /8sSystem abnormity
E5RUN-5 times /8sType mismatch
E6RUN-6 times /8sIndoor fan motor
E7RUN-7 times /8sOutdoor temperature sensor
E8RUN-8 times /8sDischarge temperature sensor
E9RUN-9 times /8sInvert module abnormity
EFRUN-10 times /8sOutdoor fan motor (DC)
EARUN-11 times /8sCurrent sensor
EERUN-12 times /8sEEPROM failure
EPRUN-13 times /8sTop of compressor temperature switch
EURUN-14 times /8sVoltage sensor
Protection Display Code List
P1RUN-winking,TIMER-1 time/8shigher or lower voltage
P2RUN- winking,TIMER-2 times /8sOver current
P4RUN- winking,TIMER-4 times /8sDischarge temperature
P5RUN-light,TIMER-5 times /8sOver cooling in cooling mode
P6RUN- light,TIMER-6 times /8sOver heating in cooling mode
P7RUN- light,TIMER-7 times /8sOver heating in heating mode
P8RUN- light,TIMER-8 times /8sOutdoor temperature too high or low
P9RUN- winking,TIMER-9 times/8sDrive protection (Overload)
P0RUN- winking,TIMER-10 times/8sModule self protection
Hyundai Air Conditioner Remote Control
Hyundai Air Conditioner Remote Control

Outdoor Failure Display

There is a LED on outdoor power board, when compressor is running; it is normally light; when no feedback of signal to power board from compressor, it will wink by lighting 1s and going out 1s. If failures happened, it will light 0.5s, go out 0.5s, winking several times and go out 3s for a cycle to indicate failures. The failure list is the follow:

Hyundai Air Conditioner Outdoor Failure Display
Hyundai Air Conditioner Outdoor Failure Display
Wink timeFailure
1IPM protection
2higher or lower voltage
3Over current
4Discharge temperature too high
5Outdoor coil temperature too high
6Drive abnormity
7Communication abnormity with indoor unit
8Compressor over heat（switch on top of compressor）
9Outdoor air temperature sensor failure
10Outdoor coil temperature sensor failure
11Outdoor discharge pipe temperature sensor failure
12Voltage sensor failure
13Current sensor failure
14IPM abnormity
15Outdoor communication abnormity
16DC fan motor no feedback
17defrosting

Hyundai Air Conditioner Manual PDF

Labels:

Comments

Post a Comment

Popular posts from this blog

AUX Air Con Error Codes

Aux Air Conditioner Troubleshooting November 3, 2018 at 9:18 pm If the following phenomena are found, the problem is not from the  air-conditioner itself. Problems The motor is heard operating but the air-conditioner dose not work when the indoor unit is powered on Causes Since the air-conditioner is powered on, it will come to working condition as long as you press the ON/OFF button of the remote control and the Signal is well received. Problems The compressor stops running but the indoor fan motor keeps working when it is at cooling mode with the indoor temperature higher than set temperature. Causes If you turn off the air-conditioner and restart it immediately, it will return to normal in 3 minutes, after that, the air-conditioner will automatically adjust the indoor fan speed to what you set. Problems The compressor works discontinuously at dehumidifying mode. Causes The air-conditioner will automatically control the working of the compressor according to the ...
4 comments
Read more

Rittal Air Conditioner Error Codes

  System messages are shown on the display screen of the Comfort controller via the displays A1 to A20 and E0. Rittal Air Conditioner Error Codes Error Codes System message Possible cause A1 Enclosure door open Door open or door limit switch incorrectly positioned A2 Internal temperature of enclosure too high Cooling capacity inadequate/unit undersized. Error as a consequence of messages A03 to A17. A3 Filter monitoring Filter mat soiled A4 Ambient temperature too high/too low Ambient temperature outside of admissible operating range (+10°C to +60°C) A5 Icing hazard Operational display in case of icing hazard. A6 PSAH pressure-operated switch Ambient temperature too high A7 Evaporator coil Lack of coolant; sensor in front of or behind condenser defective. A8 Condensate warning Condensate discharge kinked or blocked A9 Condenser fan blocked or defective Blocked or defective A10 Evaporator fan blocked or defective Blocked or defective A11 Compressor Compressor overloaded A12 Condense...
Post a Comment
Read more

Acson AC Error Codes and Troubleshooting

Acson AC Error Codes and Troubleshooting   The code indication changes as shown below, and notifies with a long beep. Wall Mounted AC Inverter Unit Error Codes Operation / Faulty Indication E1 Room air sensor contact loose / short. Check room sensor connection / change room sensor E2 Indoor coil sensor contact open. Check indoor coil sensor connection / change indoor coil sensor E3 Outdoor coil sensor contact open. Check outdoor coil sensor connection / change outdoor coil sensor E4 Compressor overload protection / Indoor / Outdoor coil sensor short. If running ampere highly increase, change the compressor. If not, replace the coil sensor E5 Gas leak. Check for leakage & repair / Top up refrigerant E6 Pump fault. Clear the clogging at drain pipe. If pump is not working, change the pump E7 Outdoor coil sensor exist (MS model). Remove outdoor coil sensor E8 Hardware error (tact switch pin short). Check for the tact switch pin condition E9 No Feedback from indoor fan. Check indoor...
Post a Comment
Read more