Skip to main content

General Electric Air Conditioner Error Codes

 GE Air Conditioner Fault Codes List:

General Electric Air Conditioner Error Codes
General Electric Air Conditioner Error Codes
Error CodesProblem-Repair
E0On 70 Pint models only - when water is not pumped out while the unit is running under the Pump mode, E0 and the pump light will flash on the display.
E1Electronic control board function error. Unplug the window air conditioner for 1 minute and then plug it back in to reset the electronic control board. If the code doesn’t clear, unplug the window air conditioner and check the wire harness connections on the electronic control board. Check the electronic control board for visible damage such as a burn mark. Replace the electronic control board if it’s damaged or defective.
E4Water bucket is full or defective bucket float switch. If the collection bucket is full, empty the bucket. If the bucket isn’t full, unplug the air conditioner and check the wire harness connections on the electronic control board. Check for a pinched or damaged wire in the wire harness between the electronic control board and the collection bucket float switch. Check the float switch for damage. If the float switch is defective, replace it.
88When power is connected to the unit, "88" will be displayed, this is normal. If a fault or error code appears on the display of the dehumidifier, disconnect power to the unit for 30 seconds. If the fault code reappears, review the Troubleshooting Tips in your Owner's Manual.

Troubleshooting Tips

Troubleshooting Tips: Save time and money! Review the chart below first and you may not need to call for service.

Problem: Air conditioner does not start

Possible Causes:

  1. The air conditioner is unplugged.
  2. The fuse is blown/circuit breaker is tripped.
  3. Power failure.
  4. The current interrupter device is tripped.

What To Do:

  1. Make sure the air conditioner plug is pushed completely into the outlet.
  2. Check the house fuse/circuit breaker box and replace the fuse or reset the breaker.
  3. If power failure occurs, turn the air conditioner OFF. When power is restored, wait 3 minutes to restart the air conditioner to prevent tripping of the com pressor overload.
  4. Press the mESEI’button located on the power cord plug.

 

GE Window Air Conditioner Error Codes
GE Window Air Conditioner Error Codes

 

Problem: Air conditioner does not cool or heat as it should

Possible Causes:

  1. Airflow is restricted.
  2. The temp control may not be set correctly.
  3. The air filter is dirty.
  4. The room may have been hot.
  5. Cold air is escaping.
  6. Cooling coils have iced up.

What To Do:

  1. Make sure there are no curtains, blinds or furniture blocking the front of the air conditioner.
  2. ln COOL mode or HEAT mode (some models), press the DECREASE- pad.
  3. Clean the filter at least every 30 days,
  4. When the air conditioner is first turned on, you need to allow time for the room to cool down.
  5. Check for open furnace registers and cold air returns,
  6. See “Air conditioner freezing up”below.

Problem: Air conditioner freezing up

Possible Causes: Ice blocks the airflow and stopsthe air conditioner from cooling the room.

What To Do:

  1. Set the controls at HIGH FAN or HIGH COOL and set the thermostat to a higher temperature to allow the ice to melt.
  2. Check filter for cleanliness.

Problem: The remote control is not working

Possible Causes:

  1. The batteries are inserted incorrectly.
  2. The batteries may be dead.

What To Do:

  1. Check the position of the batteries, They should be inserted correctly.
  2. Replace the batteries,

Problem: Water drips outside

Possible Causes: Hot, humid weather.

What To Do: This is normal.

Problem: Water drips indoors

Possible Causes: The air conditioner is not tilted to the outside.

What To Do: For proper water disposal, make sure the air conditioner case is level or slants slightly from the case from to the rear.

Problem: Water collects in basepan

Possible Causes: Moisture removed from air and drains into base pan.

What To Do: This is normal for 0 short period in areas with little humidity; normal for a longer period in very humid areas.

General Electric Air Conditioner Manual PDF

Labels:

Comments

Post a Comment

Popular posts from this blog

Rittal Air Conditioner Error Codes

  System messages are shown on the display screen of the Comfort controller via the displays A1 to A20 and E0. Rittal Air Conditioner Error Codes Error Codes System message Possible cause A1 Enclosure door open Door open or door limit switch incorrectly positioned A2 Internal temperature of enclosure too high Cooling capacity inadequate/unit undersized. Error as a consequence of messages A03 to A17. A3 Filter monitoring Filter mat soiled A4 Ambient temperature too high/too low Ambient temperature outside of admissible operating range (+10°C to +60°C) A5 Icing hazard Operational display in case of icing hazard. A6 PSAH pressure-operated switch Ambient temperature too high A7 Evaporator coil Lack of coolant; sensor in front of or behind condenser defective. A8 Condensate warning Condensate discharge kinked or blocked A9 Condenser fan blocked or defective Blocked or defective A10 Evaporator fan blocked or defective Blocked or defective A11 Compressor Compressor overloaded A12 Condense...
Post a Comment
Read more

Panasonic VRF AC Error Codes and Troubleshooting

  Indoor unit is detecting error signal from remote controller (and system controller). Panasonic Mini VRF AC Error Codes and Troubleshooting Error Codes Meaning E01 Error in receiving serial communication signal. E02 Error in transmitting serial communication signal. E03 Indoor unit is detecting error signal from remote controller. E04 Error in receiving serial communication signal. When turning on the power supply, the number of connected indoor units does not correspond to the number set. E06 Error of the outdoor unit in receiving serial communication signal from the indoor unit. E08 Indoor unit address setting is duplicated. E09 Remote controller address connector. E12 Starting auto address setting is prohibited. This alarm message shows that the auto address connector CN-A.ADD is shorted while other RC line is executing auto address operation. E15 Error in auto address setting. E16 Error in auto address setting. E20 No indoor unit is connected during auto address setting. E24 ...
Post a Comment
Read more

Vestel AC Error Codes and Troubleshooting

  Error Messages   are displayed, respectively by first the   Er   icon and then the special code (01, 02, …, 20, etc.) of the failure. In that case, do nothing to the air conditioner and contact with the Authorised Service.   Er11   and   Er13   are not error messages. If you see these messages, apply the steps under the following protection messages section. Vestel AC Error Code and Troubleshooting Error Codes Cause dF The icing on the outdoor unit is being defrosted. After the defrosting operation is accomplished, your air conditioner will continue to operate in the heating mode, the product should not be turned off while this mode is enabled. RE Make the arc control for your electrical wiring, if the problem is not fixed call for the service. If the problem comes out very frequently, contact with the authorised service. Sr In case of certain failures, in order to not to spoil you comfort, your air conditioner continues to operate despite the f...
Post a Comment
Read more