Skip to main content

Blue Star Air Conditioner Error Codes

 Blue Star Ductable AC, Window AC, Inverter AC error codes list;

Blue Star Air Conditioner Error Codes
Blue Star Air Conditioner Error Codes
Error CodesProblem
E0IDU EEPROM error
E1ODU coil medium-high error
E2IDU coil frozen protection
E4Discharge temperature high error
E5AC input over current protection
E6Communication error
E8Zero crossing error
EEODU EEPROM error
ECRefrigerant leak detection
F1Indoor room temperature sensor error
F2IDU coil temperature sensor error
F3Ambient temperature sensor error
F4ODU coil temperature sensor error
F5ODU discharge temperature sensor error
P3Drive phase current over load fault
P4DC bus bar high voltage and low voltage protection
P7IPM error
P5Compressor phase current protection
P8IPM over high temperature protection
PHAC over voltage and under voltage protection
L1Drive phase voltage over load protection
L2Drive phase voltage over low protection
L3Outdoor DC fan fault
L4Phase current sampling abnormal
LCCompressor out of step fault
LCCompressor startup failure
H6IDU fan motor error

Troubleshooting

Symptoms: Unit does not start

Possible Causes: MCB has tripped

Suggested Remedy: Reset MCB

Symptoms: Fuse has burnt

Possible Causes:

  1. Input voltage to the stabiliser is below acceptable range
  2. Replace fuse wire

Suggested Remedy:

  1. If the input voltage to the stabiliser is below the acceptable range, the airconditioner will not turn on

Symptoms: Unit does not cool even after the normal time delay of approx. 2 minutes

Possible Causes:

  1. Compressor is off (not in Auto or Cool Mode)
  2. The airflow paths of either or both the indoor & outdoor units are not free
  3. The air-filter is not clean

Suggested Remedy:

  1. Use the remote to turn the compressor on
  2. Remove all obstructions to make the airflow paths free
  3. Clean the air-filter

NOTE: If the unit still does not work, or if any other types of symptoms are encountered, shut off the mains (switch fuse unit) and call the service engineer/technician.

Blue Star Air Conditioner Remote Control

Blue Star Air Conditioner Remote Control
Blue Star Air Conditioner Remote Control

 

Blue Star Air Conditioner Manual PDF

Comments

Popular posts from this blog

Rittal Air Conditioner Error Codes

  System messages are shown on the display screen of the Comfort controller via the displays A1 to A20 and E0. Rittal Air Conditioner Error Codes Error Codes System message Possible cause A1 Enclosure door open Door open or door limit switch incorrectly positioned A2 Internal temperature of enclosure too high Cooling capacity inadequate/unit undersized. Error as a consequence of messages A03 to A17. A3 Filter monitoring Filter mat soiled A4 Ambient temperature too high/too low Ambient temperature outside of admissible operating range (+10°C to +60°C) A5 Icing hazard Operational display in case of icing hazard. A6 PSAH pressure-operated switch Ambient temperature too high A7 Evaporator coil Lack of coolant; sensor in front of or behind condenser defective. A8 Condensate warning Condensate discharge kinked or blocked A9 Condenser fan blocked or defective Blocked or defective A10 Evaporator fan blocked or defective Blocked or defective A11 Compressor Compressor overloaded A12 Condense...

Panasonic VRF AC Error Codes and Troubleshooting

  Indoor unit is detecting error signal from remote controller (and system controller). Panasonic Mini VRF AC Error Codes and Troubleshooting Error Codes Meaning E01 Error in receiving serial communication signal. E02 Error in transmitting serial communication signal. E03 Indoor unit is detecting error signal from remote controller. E04 Error in receiving serial communication signal. When turning on the power supply, the number of connected indoor units does not correspond to the number set. E06 Error of the outdoor unit in receiving serial communication signal from the indoor unit. E08 Indoor unit address setting is duplicated. E09 Remote controller address connector. E12 Starting auto address setting is prohibited. This alarm message shows that the auto address connector CN-A.ADD is shorted while other RC line is executing auto address operation. E15 Error in auto address setting. E16 Error in auto address setting. E20 No indoor unit is connected during auto address setting. E24 ...

Vestel AC Error Codes and Troubleshooting

  Error Messages   are displayed, respectively by first the   Er   icon and then the special code (01, 02, …, 20, etc.) of the failure. In that case, do nothing to the air conditioner and contact with the Authorised Service.   Er11   and   Er13   are not error messages. If you see these messages, apply the steps under the following protection messages section. Vestel AC Error Code and Troubleshooting Error Codes Cause dF The icing on the outdoor unit is being defrosted. After the defrosting operation is accomplished, your air conditioner will continue to operate in the heating mode, the product should not be turned off while this mode is enabled. RE Make the arc control for your electrical wiring, if the problem is not fixed call for the service. If the problem comes out very frequently, contact with the authorised service. Sr In case of certain failures, in order to not to spoil you comfort, your air conditioner continues to operate despite the f...